DBX DriveRack PA2

Input	(2) line inputs. (1) RTA Mic input
Input Connectors	(2) Female XLR line inputs. (1) Female XLR RTA Mic input
Input Type	Electronically balanced/RF filtered
Input Impedance	>50 kohm
A/D Converter	dbx Type IV™ Conversion System
CMRR	> 45dB
Mic Preamp Phantom Power	+15VDC (RTA)
Mic Preamp Equivalent Input Noise (EIN)	< -117dB, 22Hz-22kHz, 150 ohm (RTA)
Output	(6) Line Outputs
Output Connectors	Male XLR
Output Type	Electronically balanced, RF filtered
Output Impedance	120 Ω
Max Output	+20dBu
A/D Dynamic Range	112 dB A-weighted, 110 dB unweighted
Type IV Dynamic Range	123 dB with transient material, A-weighted, 22kHz BW; 121 dB with transient material, unweighted, 22kHz BW; 115 dB typical with program material, A-weighted, 22kHz BW
Alignment Delay	10ms per channel (60ms total)
Sample Rate	48kHz
Dynamic Range	>110 dB A-weighted, >107dB unweighted
THD+Noise	0.003% typical at +4dBu, 1kHz, 0dB input gain
Frequency Response	20Hz – 20kHz, +/- 0.5dB
Interchannel Crosstalk	< -110 dB, -120dB typical (input-to-output: < -100 dB)
Operating Voltage	100-120VAC 50/60 Hz - EU: 220-240 VAC 50/60 Hz
Power Consumption	22 W
Unit Weight	5.25 lbs. (2.4 kg)
Shipping Weight	6.75 lbs. (3.1 kg)
Dimensions	1.75” (H) x 5.75” (D) x 19” (W), 4.4cm (H) x 14.6cm (D) x 48.26cm (W)
D/A Dynamic Range	112 dB A-weighted, 110dB unweighted

~~€ 539~~

€ 492

Omassa varastossa
Toimitusaika 3-4 työpäivä

Näytä tuote

dbx 234S Stereo 2/3-taajuus, mono 4-tie Crossover

Input Connectors	1/4" TRS
Input Type	Electronically balanced/unbalanced, RF filtered
Input Impedance	Balanced >50k ohm, unbalanced >25k ohm
Max Input	>+22dBu balanced or unbalanced
CMRR	>40dB, typically >55dB at 1kHz
Output Connectors	1/4" TRS
Output Type	Impedance-balanaced/unbalanced, RF filtered
Output Impedance	Balanced 200 ohm, unbalanced 100 ohm
Max Output	>+21dBu balanced/unbalanced into 2k ohms or greater
Bandwidth	20Hz to 20kHz, +/-0.5dB
Frequency Response	< 3 Hz to > 90 kHz, +0/-3 dB
Signal to Noise Ratio	Ref: +4 dBu, 22 kHz measurement bandwidth
Signal-to-Noise (Stereo Mode)	>94dB (Low Output), >93dB (Mid Output), >90dB (High Output)
Signal-to-Noise (Mono Mode)	>94dB (Low Output, Low/Mid Output); >92dB (High/Mid Output); >88dB (High Output)
Dynamic Range	> 106 dB, unweighted, any output
THD+Noise	< 0.004% at +4 dBu, 1 kHz; < 0.04% at +20 dBu, 1 kHz
Interchannel Crosstalk	< -80 dB, 20 Hz to 20 kHz
Crossover Frequencies (Stereo Mode)	Low/Mid: 45 to 960 Hz or 450 Hz to 9.6 kHz (x10 setting); Low/High: 45 to 960 Hz or 450 Hz to 9.6 kHz (x10 setting); Mid/High 450Hz to 9.6kHz (x10 setting)
Crossover Frequencies (Mono Mode)	Low/Low-Mid: 45 to 960 Hz or 450 Hz to 9.6 kHz (x10 setting); Low-Mid/High-Mid: 450 Hz to 9.6 kHz; High-Mid/High: 450 Hz to 9.6 kHz
Crossover Filter Type	Linkwitz-Riley, 24 dB/octave, state-variable
Low cut Switch	Activates 40 Hz Butterworth, 12 dB/octave high-pass filter, one switch per channel.
Phase Invert Switch	Inverts the phase at the output, one switch per output.
x1 / x10 Switch	Multiplies the low-high(mono: low/mid and high/mid) crossover frequency range of the front-panel markings by a factor of 1 or 10, one switch per channel.
Mode Switch	Selects stereo/mono and 2/3/4-way operation
LF Sum Switch	Selects normal (stereo) or mono-summed low frequency operation and disables Ch 2’s low output phase invert LED to indicate that this output is not operational in the LF sum mode.
Indicators	Stereo Operation (Green); Mono Operation (Yellow); Low Cut (Red-per channel); x10 (Green-per channel); Phase Invert (Red-per output)
Operating Voltage	100-120 VAC 50/60Hz; 120 VAC 60Hz 230 VAC 50/60Hz
Operating Temperature	32°F to 113°F (0°C to 45°C)
Power Consumption	15W
Power Connector	IEC receptacle
Dimensions	1.75" H X 19" W X 6.9" D (4.4cm x 48.3cm x 17.5cm)
Unit Weight	4.0 lbs. (1.8 kg)
Shipping Weight	5.8 lbs. (2.6 kg)

€ 223

Omassa varastossa
Toimitusaika 3-4 työpäivä

Näytä tuote

dbx 234XS Stereo 2/3-tie, Mono 4-tie Crossover

Input Connectors	XLR
Input Type	Electronically balanced/unbalanced, RF filtered
Input Impedance	Balanced >50k ohm, unbalanced >25k ohm
Max Input	>+22dBu balanced or unbalanced
CMRR	>40dB, typically >55dB at 1kHz
Output Connectors	XLR
Output Type	Impedance-balanaced/unbalanced, RF filtered
Output Impedance	Balanced 60 ohm, unbalanced 30 ohm
Max Output	>+21dBu balanced/unbalanced into 2k ohms or greater
Bandwidth	20Hz to 20kHz, +/-0.5dB
Frequency Response	< 3 Hz to > 90 kHz, +0/-3 dB
Signal to Noise Ratio	Ref: +4 dBu, 22 kHz measurement bandwidth
Signal-to-Noise (Stereo Mode)	>94dB (Low Output), >93dB (Mid Output), >90dB (High Output)
Signal-to-Noise (Mono Mode)	>94dB (Low Output, Low/Mid Output); >92dB (High/Mid Output); >88dB (High Output)
Dynamic Range	> 106 dB, unweighted, any output
THD+Noise	< 0.004% at +4 dBu, 1 kHz; < 0.04% at +20 dBu, 1 kHz
Interchannel Crosstalk	< -80 dB, 20 Hz to 20 kHz
Crossover Frequencies (Stereo Mode)	Low/Mid: 45 to 960 Hz or 450 Hz to 9.6 kHz (x10 setting); Low/High: 45 to 960 Hz or 450 Hz to 9.6 kHz (x10 setting); Mid/High 450Hz to 9.6kHz (x10 setting)
Crossover Frequencies (Mono Mode)	Low/Low-Mid: 45 to 960 Hz or 450 Hz to 9.6 kHz (x10 setting); Low-Mid/High-Mid: 450 Hz to 9.6 kHz; High-Mid/High: 450 Hz to 9.6 kHz
Crossover Filter Type	Linkwitz-Riley, 24 dB/octave, state-variable
Low cut Switch	Activates 40 Hz Butterworth, 12 dB/octave high-pass filter, one switch per channel.
Phase Invert Switch	Inverts the phase at the output, one switch per output.
x1 / x10 Switch	Multiplies the low-high(mono: low/mid and high/mid) crossover frequency range of the front-panel markings by a factor of 1 or 10, one switch per channel.
Mode Switch	Selects stereo/mono and 2/3/4-way operation
LF Sum Switch	Selects normal (stereo) or mono-summed low frequency operation and disables Ch 2’s low output phase invert LED to indicate that this output is not operational in the LF sum mode.
Indicators	Stereo Operation (Green); Mono Operation (Yellow); Low Cut (Red-per channel); x10 (Green-per channel); Phase Invert (Red-per output)
Operating Voltage	100-120 VAC 50/60Hz; 120 VAC 60Hz 230 VAC 50/60Hz
Operating Temperature	32°F to 113°F (0°C to 45°C)
Power Consumption	15W
Power Connector	IEC receptacle
Dimensions	1.75" H X 19" W X 6.9" D (4.4cm x 48.3cm x 17.5cm)
Unit Weight	4.0 lbs. (1.8 kg)
Shipping Weight	5.8 lbs. (2.6 kg)

€ 284

Erikoistuote
Toimitetaan 5-8 arkipäivässä

Näytä tuote

LD Systems X 223 Aktiivinen crossover

Product number:	LDX223
Product type:	active crossover
Type:	analog, 2-way stereo/3-way mono
Frequency response:	20 - 20,000Hz
Dynamic range:	106dB
Signal-to-noise ratio:	> 93dB
THD:	< 0,004 %
Crosstalk:	< - 80 (20 - 20.000 Hz)dB
Max. input level:	+21 dBu (balanced or unbalanced)
Max. output level:	+21 dBu (balanced or unbalanced)
Input impedance (kOhms):	50000
Output impedance:	200Ohm(s)
Controls:	2x frequency switch x1/x10, 2 x low gain, 2 x highpass (40 Hz), mono/stereo mode, LF sum, 2 x crossover frequency low/high, 4 x inv switch, 2 x crossover low/mid, 2 x input gain, 2 x high gain
Display:	stereo, 2 x clip, 4 x inv., 2 x crossover x 10, mono, 2 x highpass
Line inputs:	2
Line input connectors:	XLR
Line outputs:	4
Line output connectors:	XLR
Mains connector:	IEC socket
Operating voltage:	220 V AC - 240 V AC
Width:	482mm
Height:	44,5mm
Depth:	153mm
Weight:	2,9kg

€ 120

Erikoistuote
Toimitetaan 5-8 arkipäivässä

Näytä tuote

dbx 223XS Stereo 2-Way/Mono 3-Way Crossover (2-tie/Mono 3-tie)

Input Connectors	XLR
Input Type	Electronically balanced/unbalanced, RF filtered
Input Impedance	Balanced >50k ohm, unbalanced >25k ohm
Max Input	>+22dBu balanced or unbalanced
CMRR	>40dB, typically >55dB at 1kHz
Output Connectors	XLR
Output Type	Impedance-balanaced/unbalanced, RF filtered
Output Impedance	Balanced 200 ohm, unbalanced 100 ohm
Max Output	>+21dBu balanced/unbalanced into 2k ohms or greater
Bandwidth	20Hz to 20kHz, +/-0.5dB
Frequency Response	< 3 Hz to > 90 kHz, +0/-3 dB
Signal to Noise Ratio	Ref: +4 dBu, 22 kHz measurement bandwidth
Signal-to-Noise (Stereo Mode)	>94dB (Low Output), >91dB (High Output)
Signal-to-Noise (Mono Mode)	>94dB (Low Output), >93dB (Mid Output), >91dB (High Output)
Dynamic Range	> 106 dB, unweighted, any output
THD+Noise	< 0.004% at +4 dBu, 1 kHz; < 0.04% at +20 dBu, 1 kHz
Interchannel Crosstalk	< -80 dB, 20 Hz to 20 kHz
Crossover Frequencies (Stereo Mode)	Low/High: 45 to 960 Hz or 450 Hz to 9.6 kHz (x10 setting)
Crossover Frequencies (Mono Mode)	Low/Mid: 45 to 960 Hz or 450 Hz to 9.6 kHz (x10 setting); Mid/High: 45 to 960 Hz or 450 Hz to 9.6 kHz (x10 setting)
Crossover Filter Type	Linkwitz-Riley, 24 dB/octave, state-variable
Low cut Switch	Activates 40 Hz Butterworth, 12 dB/octave high-pass filter, one switch per channel.
Phase Invert Switch	Inverts the phase at the output, one switch per output.
x1 / x10 Switch	Multiplies the low-high(mono: low/mid and high/mid) crossover frequency range of the front-panel markings by a factor of 1 or 10, one switch per channel.
Mode Switch	Selects stereo/mono and 2/3-way operation
LF Sum Switch	Selects normal (stereo) or mono-summed low frequency operation and disables Ch 2’s low output phase invert LED to indicate that this output is not operational in the LF sum mode.
Indicators	Stereo Operation (Green); Mono Operation (Yellow); Low Cut (Red-per channel); x10 (Green-per channel); Phase Invert (Red-per output)
Operating Voltage	100 VAC 50/60 Hz; 120 VAC 60 Hz 230 VAC50 HZ
Operating Temperature	32°F to 113°F (0°C to 45°C)
Power Consumption	15W
Power Connector	IEC receptacle
Dimensions	1.75" H X 19" W X 6.9" D (4.4cm x 48.3cm x 17.5cm)
Unit Weight	3.7 lbs. (1.7 kg)
Shipping Weight	5.4 lbs. (2.5 kg)

~~€ 203~~

€ 198

Erikoistuote
Toimitetaan 5-8 arkipäivässä

Näytä tuote

Asiakaspalvelu

Asiakaspalvelu

Jakosuotimet

dbx DriveRack PA2 -prosessori

DBX DriveRack PA2

dbx 234S Stereo 2/3-taajuus, mono 4-tie Crossover

dbx 234XS Stereo 2/3-tie, Mono 4-tie Crossover

LD Systems X 223 Aktiivinen crossover

dbx 223XS Stereo 2-Way/Mono 3-Way Crossover (2-tie/Mono 3-tie)

Asiakaspalvelu

AI-avustaja